Histórico de Commits

Autor SHA1 Mensagem Data
  Pau Lleonart Calvo 33ecb151c6 Groups: limit which filaments a group may print with (#3522) (#3567) há 3 dias atrás
  maziggy ed0742c781 MQTT: the debug log shows what a reported command contains (#3531) há 4 dias atrás
  maziggy 7264f27963 Long uploads: wait for the full file, no stale reconnect (#3538) há 1 semana atrás
  Keybored 053ac2b1a6 Printers: show each H2C nozzle's print time (#3507) há 1 semana atrás
  maziggy cd90e17331 Printers: a partial external spool push no longer empties the slot (#3513) há 1 semana atrás
  maziggy a0326afd08 Printers: the H3C card shows the hotend on the toolhead (#3442) há 1 semana atrás
  maziggy f0a755bee6 AMS: an A2L with an AMS and an AMS Lite shows both (#3499) há 1 semana atrás
  maziggy bae60ed5b4 MQTT: a print paused at startup resumes as the same print (#3485) há 1 semana atrás
  maziggy 6eaca0ef5c H3C: review fixes (#3442) há 1 semana atrás
  Dalton Clift 9ae30fb352 Bambu Lab H3C support (#3442) há 1 semana atrás
  maziggy e0955820fc Clear a print_error fault once the printer clears it (#3487) há 1 semana atrás
  maziggy 2c95725032 MQTT: a reconnect never re-sends the old connection's commands há 2 semanas atrás
  maziggy 080d866fbb K-profile read: no answer is an error, not an empty table há 3 semanas atrás
  maziggy 2e18689226 fix(printers): X2D aux fans named the right way round (issue #3373) há 3 semanas atrás
  maziggy 8901ff849a feat(printers): time to the next slicer pause, and a heads-up (issue #2984) há 4 semanas atrás
  maziggy 1e30e32661 fix(archives): a print that finishes while Bambuddy restarts is completed (issue #3310) há 4 semanas atrás
  maziggy ad62d10636 fix(printers): an unplugged AMS leaves the printer card (issue #3356) há 4 semanas atrás
  maziggy 0a7b7c6075 fix(printers): no-AMS printers print from the spool holder (issue #3356) há 4 semanas atrás
  maziggy 5eae043592 fix(ams): AMS Lite shows its serial and firmware (issue #3348) há 4 semanas atrás
  maziggy 4142c5dcab fix(inventory): spool replaced mid-print is charged its part (issue #3325) há 4 semanas atrás
  maziggy a8dd164c71 fix(spoolman): failed print is charged only for what it used (issue #3317) há 1 mês atrás
  maziggy 460c11ca30 chore: remove dead code (audit step 4): unused backend helpers and schema classes, 51 unused API client wrappers, test-only components (BackupModal, RestoreModal, VirtualPrinterSettings, TagDetectedModal, WeightDisplay, useLongPress) and their translations; removed POST /printers/test, the two printer debug routes and the SpoolBuddy update-status channel; legacy virtual printer settings fields removed from the settings API; first-run setup redirect tested há 1 mês atrás
  maziggy ac4806f029 fix: a failed first run no longer leaves the archive at its partial cost (built-in inventory); completion stops the start cost estimate before writing the real cost; 2FA/SSO logins report LDAP/OIDC users' auth source; a fault in both print_error and HMS is listed once; a refused H2D load's tray target expires; refused K-profile re-applies are logged; the cloud filament-name map is fetched once per account without holding a DB connection; the library edit route refuses folder changes across the external boundary; a slow slice-progress answer is not reported as an unreachable sidecar há 1 mês atrás
  maziggy 2b5cd87c7f fix(queue): pipeline cancel stops the preheat and frees the budget; an offline stop frees the budget; the SD cleanup at a print's end is bounded to 45 s; a refused print start is logged and retried at once without a reconnect há 1 mês atrás
  maziggy e05a917445 fix(notifications,drying): printer-limited channels get only their printer's events; blocking mode pre-dries for scheduled jobs; model jobs say "(drying)"; remove dead load-tray state há 1 mês atrás
  maziggy e3824097fa fix(mqtt): an H2D's active slot is read against the same message's nozzle data, and older nozzle data no longer overrules it há 1 mês atrás
  maziggy 26e9a05707 fix(queue): a plate printed from the external spool keeps the AMS off on multi-plate files; slot reuse respects the finish; any-model VPs keep the AMS on; cloud filament id read from the preset too há 1 mês atrás
  maziggy f45cc599f3 fix(kprofiles): an AMS change leaves the K-profile to the lost-selection check; command answers no longer change the nozzle; unconfirmed writes say so and edits read back; skip refusals are logged; stop-drying toast says sent há 1 mês atrás
  maziggy cacaaf4dae fix(printers): live status carries nozzles, firmware, developer mode and the print's AMS mapping; run-out hint narrows by nozzle; AMS-HT is its unit id; rotate check sees loaded slots há 1 mês atrás
  maziggy 5a9415e2e1 fix(ams): Load and Unload work on an AMS-HT há 1 mês atrás