|
|
@@ -30,6 +30,7 @@ All notable changes to Bambuddy will be documented in this file.
|
|
|
- **Choose which printer an "Any model" job takes (#2915, requested by @bryanmahin, contributed by @Keybored02 in #3547)** — Several printers of a model can take an "Any model" job, and the one with the fewest print hours always got it. **Settings > Workflow > Printer Order for Any-Model Jobs** now chooses: the fewest print hours (the default, as before), the most (use up the machines near replacement first), the printer idle the longest (by its last finished print; one that never printed goes first), or the printers' own priority, a number in **Edit Printer** (lowest first, none last). The order only ranks printers that can take the job: a busy, offline or filament-short printer is still passed over, and preferred colours still come first. Powering a printer on with an Auto Power On plug follows the same order.
|
|
|
|
|
|
### Fixed
|
|
|
+- **"Any model" queue jobs only go to a printer whose nozzle fits (#3536, reported and fixed by @Eifel-Joe in #3554)** — A job queued for any printer of a model went to the first free one without looking at its nozzle, and the nozzle check before the start then failed it, even when another printer of the model had the right nozzle. With two A1s (0.4 mm and 0.6 mm), a file sliced for 0.6 mm could fail on the 0.4 mm one. Now a printer whose nozzles, including the nozzle rack on an H2C, don't fit the file is passed over. If no printer of the model fits, the job waits with "No A1 has a 0.6mm nozzle: ..." instead of failing, and starts by itself once a matching nozzle is fitted. A file or printer without a known nozzle size counts as fitting, as before. Waking a printer with its smart plug, moving a job held for low filament and auto-drying use the same check. A job for one specific printer is unchanged.
|
|
|
- **Spool labels print Polish, Czech, Cyrillic and Greek letters (#3553, reported by @wsciekly83)** — Label PDFs used the PDF base font Helvetica, which only has Western European characters, so letters like ą, ę, ł, ś or ż and any Cyrillic or Greek text came out as empty boxes, although the inventory showed them correctly. Labels now embed Liberation Sans, which has the same letter widths, so the layout is unchanged. Chinese and Japanese characters are not covered yet
|
|
|
- **The spool CSV import reads files saved by Excel with European regional settings (#3523, reported and fixed by @jayhemnani9910 in #3529)** — Excel in a comma-decimal locale (German, French, Dutch, Italian, ...) saves CSV with `;` between the fields and `,` as the decimal mark. The import only read commas, so the whole header became one unknown column and nothing was imported ("Required column 'material' is missing"). The separator is now taken from the header line, and in a `;` file a decimal comma in `cost_per_kg` and `weight_used` is read as a decimal point, so `24,99` imports as 24.99. Comma-separated files are read as before. Wiki updated.
|
|
|
- **Long uploads to an A1 no longer end in a failed or unreadable print (#3538, reported by @SaadShaya7)** — Two problems at the handoff from a slow upload to the print command, seen with a 19 MB file that took three minutes. When the printer didn't confirm the upload, Bambuddy read the file size back, logged that the file was incomplete, and sent the print command anyway: the printer was still writing the file and either stayed idle or reported that it could not parse it. Bambuddy now keeps reading the size for up to two minutes, sends the print command once the file is complete, and otherwise retries the upload. And because the A1 sends no status while it receives a file, Bambuddy took the silence for a dead connection and reconnected just before the print command, which then failed the job. Silence during an upload, and in the minute after it, no longer counts as a dead connection; this also applies to firmware uploads.
|