|
@@ -24,6 +24,7 @@ All notable changes to Bambuddy will be documented in this file.
|
|
|
- **RFID Spool Data Erased by Periodic AMS Updates** — Periodic MQTT push-all responses cleared `tag_uid` and `tray_uuid` fields because they were included in the "always update" list. These fields are now preserved during updates and only cleared when a spool is physically removed (slot clearing detected by empty `tray_type`). This fixes the AMS "eye" icon disappearing for RFID spools after startup.
|
|
- **RFID Spool Data Erased by Periodic AMS Updates** — Periodic MQTT push-all responses cleared `tag_uid` and `tray_uuid` fields because they were included in the "always update" list. These fields are now preserved during updates and only cleared when a spool is physically removed (slot clearing detected by empty `tray_type`). This fixes the AMS "eye" icon disappearing for RFID spools after startup.
|
|
|
- **AMS Slot Configuration Overwrites RFID Spool State** — Configuring an AMS slot for an RFID-detected Bambu Lab spool sent `ams_set_filament_setting`, which replaced the firmware's RFID-managed filament config with a manual one — causing the slicer's "eye" icon to change to a "pen" icon. Now detects RFID spools and skips the filament setting command, only sending K-profile selection.
|
|
- **AMS Slot Configuration Overwrites RFID Spool State** — Configuring an AMS slot for an RFID-detected Bambu Lab spool sent `ams_set_filament_setting`, which replaced the firmware's RFID-managed filament config with a manual one — causing the slicer's "eye" icon to change to a "pen" icon. Now detects RFID spools and skips the filament setting command, only sending K-profile selection.
|
|
|
- **K-Profile Selection Corrupts Existing Profiles on X1C/P1S** — The `extrusion_cali_sel` command included a `setting_id` field that BambuStudio never sends, causing firmware to mislink calibration data. The `extrusion_cali_set` command was sent unconditionally, overwriting existing profile metadata. Now `setting_id` is removed from selection commands, and `extrusion_cali_set` is only sent when no existing profile is selected (`cali_idx < 0`).
|
|
- **K-Profile Selection Corrupts Existing Profiles on X1C/P1S** — The `extrusion_cali_sel` command included a `setting_id` field that BambuStudio never sends, causing firmware to mislink calibration data. The `extrusion_cali_set` command was sent unconditionally, overwriting existing profile metadata. Now `setting_id` is removed from selection commands, and `extrusion_cali_set` is only sent when no existing profile is selected (`cali_idx < 0`).
|
|
|
|
|
+- **AMS Slot Configure — Black Filament Color Not Pre-Populated** — When re-opening the Configure AMS Slot modal for a slot with black filament, the color field was empty despite the preset and K-profile being correctly pre-selected. The color pre-population logic excluded hex `000000` (black) as a guard against empty slots, but empty slots already skip color data entirely. Removed the unnecessary check so black is now pre-populated like any other color.
|
|
|
|
|
|
|
|
### Improved
|
|
### Improved
|
|
|
- **SQLite WAL Mode for Database Reliability** — Database now uses Write-Ahead Logging (WAL) mode with a 5-second busy timeout, reducing "database is locked" errors under concurrent access. WAL mode allows simultaneous reads during writes, improving responsiveness for multi-printer setups. Automatically enabled on startup.
|
|
- **SQLite WAL Mode for Database Reliability** — Database now uses Write-Ahead Logging (WAL) mode with a 5-second busy timeout, reducing "database is locked" errors under concurrent access. WAL mode allows simultaneous reads during writes, improving responsiveness for multi-printer setups. Automatically enabled on startup.
|
maziggy