Fix OK button in F4 (#259)

* fix OK button in F4
* return DFU serial to make

firmware/targets/f3/f3-1/Src/gpio.c

@@ -79,7 +79,7 @@ void MX_GPIO_Init(void)
 
   /*Configure GPIO pin : PtPin */
   GPIO_InitStruct.Pin = BUTTON_OK_Pin;
-  GPIO_InitStruct.Mode = GPIO_MODE_IT_RISING;
+  GPIO_InitStruct.Mode = GPIO_MODE_IT_RISING_FALLING;
   GPIO_InitStruct.Pull = GPIO_NOPULL;
   HAL_GPIO_Init(BUTTON_OK_GPIO_Port, &GPIO_InitStruct);
 

firmware/targets/f3/f3-1/f3-1.ioc

@@ -373,7 +373,7 @@ RCC.HSE_VALUE=32000000
 RCC.FCLK2Freq_Value=32000000
 FREERTOS.configUSE_TIMERS=1
 NVIC.DebugMonitor_IRQn=true\:0\:0\:false\:false\:true\:false\:false\:false
-PH3-BOOT0.GPIOParameters=GPIO_Label
+PH3-BOOT0.GPIOParameters=GPIO_Label,GPIO_ModeDefaultEXTI
 Mcu.IP10=SPI2
 NVIC.SysTick_IRQn=true\:0\:0\:false\:false\:false\:false\:false\:false
 Mcu.IP12=TIM1
@@ -513,6 +513,7 @@ VP_ADC1_Vref_Input.Signal=ADC1_Vref_Input
 SH.SharedAnalog_PC5.1=ADC1_IN14,IN14-Single-Ended
 OSC_OUT.Locked=true
 PA4.GPIOParameters=GPIO_Label
+PH3-BOOT0.GPIO_ModeDefaultEXTI=GPIO_MODE_IT_RISING_FALLING
 PB15.GPIOParameters=GPIO_Label
 RCC.IPParameters=ADCFreq_Value,AHB2CLKDivider,AHBFreq_Value,APB1Freq_Value,APB1TimFreq_Value,APB2Freq_Value,APB2TimFreq_Value,APB3Freq_Value,Cortex2Freq_Value,CortexFreq_Value,EnbaleCSS,FCLK2Freq_Value,FCLKCortexFreq_Value,FamilyName,HCLK2Freq_Value,HCLK3Freq_Value,HCLKFreq_Value,HCLKRFFreq_Value,HSE_VALUE,HSI48_VALUE,HSI_VALUE,I2C1Freq_Value,I2C3Freq_Value,LCDFreq_Value,LPTIM1Freq_Value,LPTIM2Freq_Value,LPUART1Freq_Value,LSCOPinFreq_Value,LSI_VALUE,MCO1PinFreq_Value,MSIOscState,PLLM,PLLPoutputFreq_Value,PLLQoutputFreq_Value,PLLRCLKFreq_Value,PLLSAI1N,PLLSAI1PoutputFreq_Value,PLLSAI1QoutputFreq_Value,PLLSAI1RoutputFreq_Value,PLLSourceVirtual,PREFETCH_ENABLE,PWRFreq_Value,RFWKPFreq_Value,RNGFreq_Value,RTCClockSelection,RTCFreq_Value,SAI1Freq_Value,SMPS1Freq_Value,SMPSCLockSelectionVirtual,SMPSFreq_Value,SYSCLKFreq_VALUE,SYSCLKSource,USART1Freq_Value,USBFreq_Value,VCOInputFreq_Value,VCOOutputFreq_Value,VCOSAI1OutputFreq_Value
 ProjectManager.AskForMigrate=true

make/rules.mk

@@ -59,7 +59,7 @@ $(OBJ_DIR)/flash: $(OBJ_DIR)/$(PROJECT).bin
 	touch $@
 
 $(OBJ_DIR)/upload: $(OBJ_DIR)/$(PROJECT).bin
-	dfu-util -D $(OBJ_DIR)/$(PROJECT).bin -a 0 -s $(FLASH_ADDRESS)
+	dfu-util -D $(OBJ_DIR)/$(PROJECT).bin -a 0 -s $(FLASH_ADDRESS) -S $(DFU_SERIAL)
 	touch $@
 
 $(ASSETS): $(ASSETS_SOURCES)